Change language:

AMBPI PRODUCTS

AM 45 TILE ADHESIVE

AM 45
TILE ADHESIVE

AM 45 is a special tile adhesive made for interior use in housing and offices. If used in the right way, it can prevent exposing the tiles (Popping). Easy to use and efficient in materials usage.


ADVANTAGES

  • Power is strong.
  • Powerful and durable.
  • Practical and easy to apply.

APPLICATION AREA

  • Interior.
  • Dry and Wet.
  • Floor and Walls.
  • In Housing and offices.
  • Low to medium traffic area.

TYPES OF TILES

  • Homogeneous Tiles.
  • Ceramic Tiles.
  • Natural stone.
  • Mosaic.

SUBSTRATES

Concrete, screed, plaster.

1. PREPARATION PHASE

  • Keep the fields as flat as possible to save the consumption of tile adhesives.
  • Clean the application area from dust, paint, oil, grease and other impurities.
  • Then moisten the application field with a sponge / damp cloth.
  • Preferably age of plastering application / screed minimum 7 days.
  • Tiles do not need to be soaked.

2. MIXING STAGE

  • Comparison of clean water: AM 45 Powder
                            = 1 part: 3 parts.
  • Pour 3 parts AM 45 Powder bit by bit into the container
  • Mixing that already contains 1 part clean water while stirred with a spoon of cement.
  • Continue stirring with the mixer evenly until the mixture is paste-shaped.
  • Allow to stir for 5 minutes for all components to react perfectly.

3. APPLICATION STAGE

  • Repeat stirring with a cement spoon, then apply it to the application area.
  • Flatten with trowel sides are flat while pressed for a thin layer of adukan permeate to the surface of the application field.
  • Add the mixture over the first layer, drawn with a jagged trowel side, tilt angle to the surface of 60º.
  • Immediately put the ceramic over the wet layer of the mortar, tap with a rubber hammer to stick well.
  • Clean the residue from the slit between the ceramic (grout), so as not to interfere with the installation of grout filler.
  • Wait for 24 hours for the ceramic to seal perfectly.
  • Perform grout filler with an AM 50 or AM 53 grout filler.

4. EXPANSION JOINT

Places to be used for the Expansion Joint must already be determined at the time of development planning. Expansion Joints should be installed at any distance of 5 meters, any inner corners of the room, or on connections where there is a difference in building materials. The Expansion Joint shall be free of excess adhesive and shall be filled with flexible baffle materials, for example Silicone Sealant products.

NOTES:

  • Adhesives already in the trowel should be attached ceramic, do not install the ceramic on adhesive that has started to dry because it will lower the power of adhesive power.
  • Use clean water, with the amount of water that matches the mixing ratio.
  • It is recommended to make enough mix, so that every mortar is used up within 60 minutes.

TECHNICAL DATA

PRODUCT IDENTITY AM 45
SUBSTANCE Powder
COLOR Grey
BULK DENSITY (KG/LTR) 1,50 +/- 0,05 (bulk density)
DRY MIXTURE 100%
PRODUCT QUALITY CONTROL EN 12004
APPLICATION DATA
(27°C; 70% RH)
  • Open Time: 10 minutes
  • Pot Life: 60 minutes
  • Ready to Traffic (Grouting Time): 24 hours after tiles are laid
  • Full cure: 28 days
DAYA SEBAR +/- 8 m2/sack 40 kg/3 mm
PRODUCT PACKAGING

Powder :

  • 40 kg Sack
SHELF LIFE 12 month in closed condition, dry location at room temperature.

RELATED PRODUCT

CALCULATE YOUR
BUILDING NEEDS